 |
| Tools > Pullers > |
1.30 Internal Extractors
For extremely tightly packed ball bearings, bearing races, bushings, and shaft seals®.
Operation: The internal extractor is inserted into the bearing and the spindle screwed in. The sharp turned out shoulders of the pulling shell jaws will press outwards behind the part to be extracted. The counter support brace is then added. Both feet must be aligned parallel to the spindle to ensure rigidity. |
| No. |
|
|
|
 |
| 1.30/0 |
5-8 |
M 10 |
10 |
0,15 |
| 1.30/1 |
8-12 |
M 10 |
10 |
0,16 |
| 1.30/2 |
12-14 |
M 10 |
10 |
0,17 |
| 1.30/3 |
14-19 |
M 10 |
14 |
0,17 |
| 1.30/4 |
19-24 |
M 10 |
14 |
0,20 |
| 1.30/4A |
24-30 |
M 10 |
14 |
0,30 |
| 1.30/5 |
30-36 |
M 14x1,5 |
14 |
0,35 |
| 1.30/6 |
36-46 |
M 14x1,5 |
17 |
0,65 |
| 1.30/7 |
46-56 |
M 14x1,5 |
17 |
0,80 |
| 1.30/8 |
56-70 |
M 14x1,5 |
19 |
1,40 |
| 1.30/9 |
70-100 |
M 14x1,5 |
27 |
2,90 |
|
 |
 |
|
1.30 Internal Extractor, with reinforced shoulder
Special suitable for the sure & trouble free extraction of needle roller bearings, ball bearings and brass sleeves from crankshafts. Note: The soulder of the shell jaw must be applied behind the bearing. |
| No. |
|
|
|
|
| 1.30/2N |
12-14 |
M 10 |
10 |
0,17 |
| 1.30/3N |
14-19 |
M 10 |
14 |
0,17 |
1.30 Internal Extractor
Suitable for removing large ball bearings and bearing outer races.
Operation:
The extraction jaws are spread by turning the nut. The newly developed spreading system enables a simple, step free and time saving adjustment to the desired diameter to be made. The sharp edged sections of the extraction jaws seat flush beneath when spread.
| No. |
|
|
|
|
| 1.30/10 |
60-130 |
G 1/2 |
36 |
2,45 |
|
 |
|
1.35 Impact Bearing Pullers
Suited for the removal of small ball bearings since there is often not enough room for support braces.
| No. |
for internal extractor |
|
with adapter |
|
|
| 1.35/1 |
1.30/0-1.30/2 |
M 10 |
- |
17 |
0,6 |
| 1.35/2 |
1.30/0-1.30/7 |
M 10 |
M 14x1,5 |
24 |
1,4 |
|
|
|
1.36 Support Brace
For internal Extractors Nos. 1.30/0 - 1.30/9
Operation:
The support brace is placed on the housing and the spindle screwed onto the spindle of the internal extractor. The toggle is held firmly, and the bearing extracted by tightening the nut.
| No. |
for internal extractor |
|
|
|
| 1.36/1 |
1.30/1-1.30/5 |
M 10 |
27 |
0,6 |
| 1.36/2 |
1.30/6-1.30/8 |
M 14x1,5 |
32 |
1,4 |
| 1.36/3 |
1.30/9 |
M 14x1,5 |
32 |
3,0 |
1.36 Support Brace
For Internal Extractor No. 1.30/10
| No. |
for internal extractor |
|
|
|
| 1.36/4 |
1.30/10 |
G 1/2 |
36 |
7,7 |
|
 |
|
| This is to inform all visitors to our website, that the Information - technical and or otherwise, - given herein and or contained herein. In our website pages, are as per the information available with us from our principals M/s Gedore, Germany and Bolt Tech USA, through their respective catalogs. It may be noted that every efforts have been made to ensure that the information reproduced herein is correct and true, as is available with us. If there is any inaccuracy and/or discrepancy or error which has crept in, Garage Equipment & Tools co. and any of its partners, or employees, and or sister concerns, shall not be liable in any manner what so ever against any loss and or damages, directly or indirectly, caused to any party, whether in India, and or beyond India. All errors and omissions are subject to rectifications. It is also notified that all the information given herein either by Garage Equipment & Tools co. and or by M/s Gedore Germany and or M/s Bolt tech USA is for general information only and clarifications if any required, they can contact the respective parties for information. The publication of this information on the web page is solely for the purpose of General information about the products offered by M/s Gedore or M/.s Bolttech. It is possible the Information may not be complete, and may not contain full details about the range of products offered. For any further details please contact Garage Equipment & Tools co. |
|
|
